CD-21-2-CCD-21-2-C vibration speed sensor, after the intensity meter is matched, it can measure various displacements and speeds. The rotor supported by the rolling bearing will transmit vibration enough to the bearing seat, and the speed sensor mounted on the bearing housing or very close to the bearing housing, the internal moving coil cuts the magnetic line and outputs the voltage, and provides the signal to the monitoring instrument. Used to predict and alarm mechanical faults. The vibration sensor is used together with the vibration monitor to achieve continuous long-term monitoring and is suitable for measurement of mechanical vibrations such as steam turbines, fans, pumps, and coal mills. The working principle is based on a primary component that converts mechanical energy into electrical energy. It is fixed on the bracket by two coils, and a magnetic steel in the middle is connected to the casing through a spring, and the magnetic steel moves in the line. The magnetic lines of force are cut, thus generating an induced electromotive force. The voltage is proportional to the speed of the casing, which is called the vibration speed sensor. The vibration sensor produced by Zhengzhou Hangke has small volume, good sealing and long service life. Due to the double coil structure, it can superimpose the effective signal, and the interference signal attenuation effectively improves the anti-interference ability.
1. Measuring range: Frequency: 10 ~ 300Hz
Amplitude: 0 to 200um 0 to 500um 0 to 800um (peak to peak)
Intensity: 0 ~ 20mm / s 0 ~ 25mm / s 0 ~ 50mm / s (true RMS)
2. Measurement accuracy: ±0.5, linear error ≤1%FS
3. Measurement method: vertical or horizontal
4. Output signal: current output: 4 ~ 20mA (load ≤ 1KΩ)
5. Ambient temperature: -10 ~ 65 ° C (relative humidity ≤ 85%)
6. Power supply voltage: DC24V (power consumption ≤ 3W)
7. Dimensions: 35 × 75 (mm)
8. Fixed screw hole: M10×1.5×10mm
CD-7/CD-8CD-7/CD-8 vibration speed sensor resolution, temperature adaptability, suitable for seismic exploration in various environments. Mainly installed on the bearing caps of various rotating machinery, such as steam turbines, compressors, fans and pumps. It is an electromagnetic sensor that cuts magnetic lines by a moving coil and outputs a voltage. Therefore, it does not need to supply power during operation, and the explosion-proof vibration speed sensor is an inertial sensor. The vibration signal is converted into an electrical signal by the principle of magnetoelectric induction. . It is mainly composed of magnetic circuit system, inertial mass, spring damping and other parts. A magnet is rigidly fixed to the sensor, and the inertial mass (coil assembly) is suspended by a spring element. jobs.
CD-21-2-CCD-21-2-C vibration speed sensor
MLS-9W/MLV-9W/MLV-6/MLV-7/MLV-8/MLV-9200/MLV-9268/MLV-27/MT1/MT2T/MT3T/M
T3M vibration sensor
CS-CD-001/CS-CD-010/OD9200/OD9300/S6000/PR9266/PR9268/20/30/60/70/Axis vibration
Sensor MLV-9200 (16699/900) / 9200 / 74712 / 47633 / HT-2ZD-24 / ZD25 / ZDF bearing vibration speed
Sensor VB-Z9500/VB-Z9600/SJ1061/SJ1062 Magnetoelectric Vibration Speed ​​Sensor TM0782A
TM0783A
(Mo2/3Y1/3)2AlC
Storage conditions and validity:
This product should be stored in room temperature and dry place, avoid contact with acid, alkali and other liquids, long-term storage will happen slow oxidation.
Test method:
This product can be confirmed by X-ray powder diffractometer crystal results; Element composition was confirmed by energy dispersive X-ray detector. The same morphology characterization was used to characterize the particle morphology. The particle size distribution was evaluated by laser particle size analyzer.
Safety protection:
1. Health hazards
Hazardous category: Non-hazardous chemical chemical category: ceramic powder;
Route of invasion: inhalation, ingestion;
Health hazards: dust in the eye has irritation, oral stimulation of gastrointestinal tract;
2. First aid measures
Skin contact: Remove contaminated clothing and rinse skin thoroughly with running water.
Eye contact: lift eyelid and rinse with plenty of running water or normal saline for at least 15 minutes;
Inhalation: Get away from the scene to fresh air quickly;
Ingestion: drink enough warm boiled water, induce vomiting, seek medical advice;
3. Ignition and explosion characteristics and fire protection
Flammability: non-flammable;
(Mo2/3Y1/3)2Alc,(Mo2/3Y1/3)2Alc Black Powder,(Mo2/3Y1/3)2Alc Powder,High Density (Mo2/3Y1/3)2Alc
Jilin 11 Technology Co.,Ltd , https://www.11techmxene.com